Completed the Chest Frame assembly of the MGEX Strike Freedom (changlong) Model Part 2

    Same as Chest Frame Part 1 assembly, Part 2 body assembly still uses the following parts. I have prepared the following parts: A (Multicolor), B (Gold), C (Bronze), D (White Gold), E1 (White), F1 (Metallic Gray), G (Gold) x2, H1 (Black), K1 (Light Blue), L1 (Red), Metal 3D Sticker, Etched, Chest Frame Part 1 is complete.

This is my finished video of the mgex strike freedom chest frame.

I have prepared parts L1-4, H1-1, A-13, C-3, A-2. Assemble part number L1-4 into part number H1-1. Assemble part number A-13 on top of H1-1. Assemble the finished part inside part number C-3, Assemble part number A-2 on top of part number C-3 in front.

MGEX Strike Freedom - Part L1-4, Part H1-1, Part A-13

MGEX Strike Freedom - Part L1-4, Part H1-1, Part A-13

MGEX Strike Freedom - Part C-3, Part H1-1, Part A-2

MGEX Strike Freedom - Part C-3, Part H1-1, Part A-2

Assemble Chest Frame Part 1 on top, part number K1-6 assemble on the left side, part number K1-5 assemble on the right side.

MGEX Strike Freedom - Chest Frame Part 1, Part K1-6, Part K1-5

MGEX Strike Freedom - Chest Frame Part 1

MGEX Strike Freedom - Part K1-5 and Part K1-6

Prepare part numbers G-2, G-3, G-1, each needs 2 pieces. Assemble part number G-2 into G-3, G-1 will be connected to the remaining pin of G-3. After assembly is complete, install the left finishing part onto the pin of part number F1-4, the right finishing part onto the pin of part number F1-5. Assemble part number B-4 on top of part number F1-4, part number B-3 will be assembled on top of part F1-5.

MGEX Strike Freedom - Part G-2, Part G-3 and Part G-1

MGEX Strike Freedom - Part G-2, Part G-3 and Part G-1

MGEX Strike Freedom - Part F1-4 and Part F1-5

MGEX Strike Freedom - Part F1-4 and Part F1-5

MGEX Strike Freedom - Part B-4 and Part B-3

MGEX Strike Freedom - Part B-4 and Part B-3

I have placed all the finished parts in front in preparation for assembling them. 

MGEX Strike Freedom - Part finished 1,2,3

MGEX Strike Freedom - Part finished 1,2,3

Attach 3D metallic decals 1 and 2 to the left and right positions as shown in the image. Then assemble part number C-2 and the front left, part number C-1 to the front right, the rear part will assemble part number B-7, along with that will stick metallic 3D decal number 3 and 4, metallic 3D number 3 is the round dot stuck on the top left and right, and metallic 3D number 4 will be stuck on the bottom. Stick Etching Stiker 3, 4 on part number C-2 and C-1 respectively, on the back stick Etching Stiker 1, 2.

MGEX Strike Freedom - 3D metallic decals 1 and 2

MGEX Strike Freedom - Part C-2 and Part C-1

MGEX Strike Freedom - Etching Sticker 3 and 4

MGEX Strike Freedom - Part B-7

MGEX Strike Freedom - Part B-7 and Etching Sticker 1 and 1

MGEX Strike Freedom - 3D metallic decals 3 and 4

MGEX Strike Freedom - Chest Frame completed

I tried assembling the Chest Frame with the Head Frame of the model

MGEX Strike Freedom - Chest Frame and Head Frame

    The MGEX frame is complete. You can leave a comment if you find it good or if you have any other suggestions. Thanks for watching my model assembly process.